Although your device does not support this download service, it can be used to view download information. Links to downloads can be sent via e-mail for download on a computer.
Wireless Transmitter Utility
Select your operating system.
This software update program is for the customer-owned product listed above (the “affected product”), and is provided only on acceptance of the agreement listed below. By selecting “Accept” and clicking “Download”, you are held to have accepted the terms and conditions of the agreement. Be sure you understand the terms of the agreement before beginning download.
Wireless Transmitter Utility Overview
-
The Wireless Transmitter Utility is software for creating network profiles when the Ethernet feature built into the Communication Unit UT-1, D4S, or D4, or the Wireless Transmitter WT-5 or WT-4, is used.
While the WT-4 Setup Utility was dedicated software for the WT-4, this software can be used with a broader range of hardware, including the WT-4 and WT-5, so the name has been changed from WT-4 Setup Utility to Wireless Transmitter Utility.
- Precautions
-
- • This software is offered to those who use the Communication Unit UT-1, the Wireless Transmitter WT-4, WT-5, or the Ethernet feature built into the D4 or D4S.
- • This software operates from the file titled S-WTU___-010504WF-NSA__-ALL___.exe / S-WTU___-010504WF-INT__-ALL___.exe / S-WTU___-010504WF-EUR__-ALL___.exe / S-WTU___-010504WF-CND__-ALL___.exe. Download the appropriate file for your operating system to your computer and run the file.
- • Turn off all virus-scanning software and exit the Wireless Transmitter Utility, or any other application that may be running, before proceeding with this installation.
- • You must have Administrator authority to run this software on a Windows computer.
- • WT-4 Thumbnail select mode and Print mode are not supported.
- • When installing this software under Windows 8.1 or Windows 7, a Windows Security dialog will be displayed two or three times. Click Install to continue with the installation.
- • When installing this software on a computer to which the WT-4 Setup Utility has already been installed, uninstall the WT-4 Setup Utility before installing this software.
-
• Those updating from the WT-4 Setup Utility or the Wireless Transmitter Utility Ver. 1.3.0, and to which any of the following apply, must create network profiles again after installing this software before it can be used.
- - Those using the D4 with the WT-5 or an Ethernet connection in image transfer mode or camera control mode
- - Those using the WT-4 (except for connection to an FTP server in transfer mode)
- • Be sure to read the sections below before downloading this software.
|
- Download software
-
| Software name |
Wireless Transmitter Utility Ver.1.5.4 |
| Download file name |
- S-WTU___-010504WF-NSA__-ALL___.exe
- S-WTU___-010504WF-INT__-ALL___.exe
- S-WTU___-010504WF-EUR__-ALL___.exe
- S-WTU___-010504WF-CND__-ALL___.exe
|
| Copyright |
Nikon Corporation |
| Extraction |
Self extracting |
| Reproduction |
Not permitted |
System requirements |
| Processor(CPU/Model) |
1.6 GHz or better Intel Celeron/Pentium 4/Core series |
| Supported OS |
- Microsoft Windows 8.1
- Microsoft Windows 8.1 Pro
- Microsoft Windows 8.1 Enterprise
- Microsoft Windows 7 Home Basic (Service Pack 1)
- Microsoft Windows 7 Home Premium (SP1)
- Microsoft Windows 7 Professional (SP1)
- Microsoft Windows 7 Enterprise (SP1)
- Microsoft Windows 7 Ultimate (SP1)
- * Pre-installed versions only.
- * Both the 32- and 64-bit versions of Windows 8.1 and Windows 7 are supported.
|
| Memory(RAM) |
Windows 8.1, Windows 7: 1 GB or more (2 GB or more recommended) |
| Hard-disk space |
500 MB or more (1 GB or more recommended) on the startup disk for both installation and when running |
| Monitor |
- Resolution: 1024 x 768 pixels (XGA) or more (1280 x 1024 pixels (SXGA) or more recommended)
- Color: 24-bit color or better
|
| Supported models |
- Communication Unit UT-1 (including use with the WT-5)
- (can be used with the D4S, D4, D810, D800, D800E, D750, D7200, D7100, and D7000)
-
- D4S, D4 (supports Ethernet feature built into the camera)
-
- Wireless Transmitter WT-5
- Supported cameras: D4S, D4
-
- Wireless Transmitter WT-4
- Supported cameras: D4S, D4, D3X, D3S, D3, D800, D800E, D700, D300S, D300, D7000
|
| Notes |
- Note regarding Windows 8.1
- Windows 8.1 does not support ad hoc wireless LAN connection.
-
- UT-1 and compatible camera firmware
- Please be sure that UT-1 firmware is the latest version when used with the following cameras.
- • D810, D750, D7200, D7100
- • D800 and D800E running A and B firmware Ver. 1.10 or later:
-
- WT-4 firmware
- When this software is used with the WT-4, please be sure that the WT-4 is running firmware Ver. 1.1.
|
- Modifications enabled with Ver. 1.5.4
-
- • Support for the D7200 has been added.
- • Support for the Communication Unit UT-1 Firmware Ver. 2.3 has been added.
- • Windows Vista is no longer supported.
|
- Precautions for use with the UT-1
-
- • When the UT-1 is connected to the D4 or D7000, Thumbnail select mode and Print mode will be displayed in addition to Transfer mode and PC mode. However, these modes cannot be used with the UT-1.
- • When the Wireless Transmitter Utility is launched to create a network profile for use with the D4S, D4 or D7000, be sure to select the WT-4/UT-1 (functions as a WT-4) option in the Select hardware dialog.
- • When the Wireless Transmitter Utility is launched to create a network profile for use with the D7100, or the D800 or D800E (running A and B firmware Ver. 1.10), be sure to select the Wired LAN option in the Select hardware dialog. When the UT-1 is used with the WT-5, select the WT-5 (Wireless LAN) option.
- • When using the UT-1 with the D4S or D4, always set Network > Choose hardware in the camera setup menu to WT-4.
|
- Transferring movies recorded with the D4S, D4, D3S, D800, D800E, D300S and D7000 (WT-4)
-
The following modes support movie transfer.
| D3S and D300S | : Transfer mode |
| D4S, D4, D800, D800E and D7000 | : Transfer mode and PC mode |
However, the Auto send and Send folder transfer settings for transfer mode are not supported.
Use transfer mode to transfer movies as follows.
- Connect to the network in transfer mode.
- Select one or more movies in full-frame or thumbnail playback mode.
-
Transfer begins when transfer marking is applied to the selected movie(s) as indicated below.
| D4S, D4 | : Hold down the OK button and press the center button on the multi selector. |
| D3S | : Hold down the thumbnail/playback zoom button and press the center button on the multi selector. |
| D800, D800E, D300S | : Press the camera’s OK button. |
| D7000 | : Hold down the BKT button and press the OK button. |
- Installation
-
- Create a new folder with an appropriate name on your computer's hard disk.
- Download S-WTU___-010504WF-NSA__-ALL___.exe / S-WTU___-010504WF-INT__-ALL___.exe / S-WTU___-010504WF-EUR__-ALL___.exe / S-WTU___-010504WF-CND__-ALL___.exe to the folder created in step 1.
- Run S-WTU___-010504WF-NSA__-ALL___.exe / S-WTU___-010504WF-INT__-ALL___.exe / S-WTU___-010504WF-EUR__-ALL___.exe / S-WTU___-010504WF-CND__-ALL___.exe to launch the software installer.
- Follow the on-screen instructions to accurately complete the installation.
- Precautions
-
- • This software is offered to those who use the Communication Unit UT-1, the Wireless Transmitter WT-4, WT-5, or the Ethernet feature built into the D4 or D4S.
- • This software operates from the file titled S-WTU___-010504MF-NSA__-32BIT_.dmg / S-WTU___-010504MF-INT__-32BIT_.dmg / S-WTU___-010504MF-EUR__-32BIT_.dmg / S-WTU___-010504MF-CND__-32BIT_.dmg. Download the appropriate file for your operating system to your computer and run the file.
- • Turn off all virus-scanning software and exit the Wireless Transmitter Utility, or any other application that may be running, before proceeding with this installation.
- • You must enter the Admin password to run this software on a Mac computer.
- • WT-4 Thumbnail select mode and Print mode are not supported.
- • When installing this software under Windows 8.1, Windows 7, a Windows Security dialog will be displayed two or three times. Click Install to continue with the installation.
- • When installing this software on a computer to which the WT-4 Setup Utility has already been installed, uninstall the WT-4 Setup Utility before installing this software.
-
• Those updating from the WT-4 Setup Utility or the Wireless Transmitter Utility Ver. 1.3.0, and to which any of the following apply, must create network profiles again after installing this software before it can be used.
- - Those using the D4 with the WT-5 or an Ethernet connection in image transfer mode or camera control mode
- - Those using the WT-4 (except for connection to an FTP server in transfer mode)
- • Be sure to read the sections below before downloading this software.
|
- Download software
-
| Software name |
Wireless Transmitter Utility Ver.1.5.4 |
| Download file name |
- S-WTU___-010504MF-NSA__-32BIT_.dmg
- S-WTU___-010504MF-INT__-32BIT_.dmg
- S-WTU___-010504MF-EUR__-32BIT_.dmg
- S-WTU___-010504MF-CND__-32BIT_.dmg
|
| Copyright |
Nikon Corporation |
| Extraction |
Self extracting |
| Reproduction |
Not permitted |
System requirements |
| Processor(CPU/Model) |
Intel Core series/Xeon series |
| Supported OS |
- OS X 10.10.2
- OS X 10.9.5
- OS X 10.8.5
|
| Memory(RAM) |
2 GB or more |
| Hard-disk space |
500 MB or more (1 GB or more recommended) on the startup disk for both installation and when running |
| Monitor |
- Resolution: 1024 x 768 pixels (XGA) or more (1280 x 1024 pixels (SXGA) or more recommended)
- Color: 24-bit color (millions of colors) or better
|
| Supported models |
- Communication Unit UT-1 (including use with the WT-5)
- (can be used with the D4S, D4, D810, D800, D800E, D750, D7200, D7100, and D7000)
-
- D4S, D4 (supports Ethernet feature built into the camera)
-
- Wireless Transmitter WT-5
- Supported cameras: D4S, D4
-
- Wireless Transmitter WT-4
- Supported cameras: D4S, D4, D3X, D3S, D3, D800, D800E, D700, D300S, D300, D7000
|
| Notes |
- UT-1 and compatible camera firmware
- Please be sure that UT-1 firmware is the latest version when used with the following cameras.
- • D810, D750, D7200, D7100
- • D800 and D800E running A and B firmware Ver. 1.10 or later:
-
- WT-4 firmware
- When this software is used with the WT-4, please be sure that the WT-4 is running firmware Ver. 1.1.
|
- Modifications enabled with Ver. 1.5.4
-
- • Support for the D7200 has been added.
- • Support for the Communication Unit UT-1 Firmware Ver. 2.3 has been added.
|
- Precautions for use with the UT-1
-
- • When the UT-1 is connected to the D4 or D7000, Thumbnail select mode and Print mode will be displayed in addition to Transfer mode and PC mode. However, these modes cannot be used with the UT-1.
- • When the Wireless Transmitter Utility is launched to create a network profile for use with the D4S, D4 or D7000, be sure to select the WT-4/UT-1 (functions as a WT-4) option in the Select hardware dialog.
- • When the Wireless Transmitter Utility is launched to create a network profile for use with the D7100, or the D800 or D800E (running A and B firmware Ver. 1.10), be sure to select the Wired LAN option in the Select hardware dialog. When the UT-1 is used with the WT-5, select the WT-5 (Wireless LAN) option.
- • When using the UT-1 with the D4S or D4, always set Network > Choose hardware in the camera setup menu to WT-4.
|
- Transferring movies recorded with the D4S, D4, D3S, D800, D800E, D300S and D7000 (WT-4)
-
The following modes support movie transfer.
| D3S and D300S | : Transfer mode |
| D4S, D4, D800, D800E and D7000 | : Transfer mode and PC mode |
However, the Auto send and Send folder transfer settings for transfer mode are not supported.
Use transfer mode to transfer movies as follows.
- Connect to the network in transfer mode.
- Select one or more movies in full-frame or thumbnail playback mode.
-
Transfer begins when transfer marking is applied to the selected movie(s) as indicated below.
| D4S, D4 | : Hold down the OK button and press the center button on the multi selector. |
| D3S | : Hold down the thumbnail/playback zoom button and press the center button on the multi selector. |
| D800, D800E, D300S | : Press the camera’s OK button. |
| D7000 | : Hold down the BKT button and press the OK button. |
- Installation
-
- Download S-WTU___-010504MF-NSA__-32BIT_.dmg / S-WTU___-010504MF-INT__-32BIT_.dmg / S-WTU___-010504MF-EUR__-32BIT_.dmg / S-WTU___-010504MF-CND__-32BIT_.dmg.
- Double-click the S-WTU___-010504MF-NSA__-32BIT_.dmg / S-WTU___-010504MF-INT__-32BIT_.dmg / S-WTU___-010504MF-EUR__-32BIT_.dmg / S-WTU___-010504MF-CND__-32BIT_.dmg icon to mount the disk image titled, S-WTU___-010504MF-NSA__-32BIT_ / S-WTU___-010504MF-INT__-32BIT_ / S-WTU___-010504MF-EUR__-32BIT_ / S-WTU___-010504MF-CND__-32BIT_. A file titled Welcome will be created inside the disk image.
- Run S-WTU___-010504MF-NSA__-32BIT_ / S-WTU___-010504MF-INT__-32BIT_ / S-WTU___-010504MF-EUR__-32BIT_ / S-WTU___-010504MF-CND__-32BIT_ to launch the software installer.
- Follow the on-screen instructions to accurately complete the installation.
